 |
|
|
 |
 |
|
|
Elliott Machine Works 50K Service Truck
2008 Ford F750, Elliott D-26 Mechanics Body, Venturo HT50KX-25' all hydraulic hex boom crane (Stock #1505)
|
|
   |
|
 |
- 2008 Ford F750
- 6.7L Cummins 240 HP @ 2400 RPM
- Allison 2500 5-speed
- Rear Axle 5.57
- Air brakes
- 10,000# FA; 21,000# RA –Derate 25,999#
- Air ride driver
- XL trim
- Steel wheels; 22.5x8.25 – 11R22.5 tires
|
 |
|
|
|
| |
|
|
- SERVICE BODY
* Type: ‘Elliott’ model D-26, all-steel, all-welded construction
* Length: 136 inches
* Width: 96 inches
* Crane base: Curbside rear 66,000 ft/lb capacity
* Side packs: 60” high x 23” deep – galvanneal construction
* Long sills: Full-length, rectangular steel tubing, 6” x 3” x 0.25” per ASTM A-500-B
* Cross members: Structural/formed steel channel 3.00 inches spaced on 12.00 inches
* Floor: Steel floor with Rumber flooring installed full width/length
* Bulkhead: Front, formed galvanneal steel, protects hydraulic reservoir
* Crane base: Curb side rear, structural steel with steel wrap. Reinforced to main platform long sills using rectangular steel tubing
* Load rings: Recessed tie down rings 6 each located in load bed area
* Material: Galvanneal steel, .1046 inch
* Doors: Reinforced galvanneal steel – single panel
* Hinges: Stainless steel, strap-type, heavy duty
* Latches: Recess ‘T’ handle, multi-point w/keyed lock (keyed alike)
* Seals: Automotive-type, closed cell, full perimeter
* Door holders: Gas shock on all vertical doors
* Compartments: 7- tool drawer set SS-1, bolt bin SS-2, 7-tool drawer set SS-3, Oxy/Acet w/adj. shelf CS-1
- CRANE AND OUTRIGGERS
* Make/Model: Venturo model HT50KXP-25, hydraulic-proportional; power extension to 24’-10”
* 60 ft/min; 400o power rotation; 100’ 3/8” aircraft cable; capacity overload shut-off
* Capacity: 8,000 lbs. maximum lift; 2000 lbs. at full extension
* Reach: 24’10” maximum reach
* Controls: Radio (wireless) control including air compressor “on-off”, chassis engine “start-stop”, chassis engine high idle “on-off”
* Outriggers: Rear-mount, full hydraulic “in-out”, “up-down”
- Hydraulic System
* Type: Central ‘open-loop’, power take-off driven tandem hydraulic pump
* PTO: Transmission-mounted, heavy duty, rated for horsepower and torque load
* Pump: Hydraulic, tandem, gear-type
- Reservoir: Hydraulic oil, 40 U.S. gallons, steel construction, installed on front bulkhead
- Air Supply System
* Air compressor: Hydraulic-powered, reciprocating compressor
* Make/model: EM 30
* Output: 30 CFM @ 100 psi
* Air receiver: ASME-certified, installed underbody with accessible drain valve cable
* FLR: Filter, lubricator, regulator installed in load bed area
* Hose reel: Hannay spring-return reel located top of drivers’ side pack
* Service hose: 1/2” x 50’ long
- Accessory Group
* Bumper: Rear, heavy-duty bumper with full width storage compartment
* Access doors located both sides
* Bumper top surface is coated with raptor heavy duty surface material
* Curbside rear vise plate
* 2” square hitch receiver tube
* Lighting: FMVSS-108 clearance lighting, stop-tail-turn, LED
* Finish coating: Coated surfaces are phosphate-etched, air-dried, and finished with 2 coats of PPG epoxy-primer and PPG Essential acrylic urethane. All finish coatings are oven-baked. Load space covered Rumber flooring – side walls are Raptor coated
* Reverse alarm: 12 VDC electric back-up alarm
|
|
|
|
|
| |
|
|
- Factory Direct Price = $93,000 (total price excluding tax, title, and license fees)
- Stock # 1505
- F.O.B. Cincinnati, Ohio
- Available for IMMEDIATE delivery
|
|
|
|
|
| |
|
|
|
 |
 |
 |
| |
